ECOM Symbol ECOM Symbol

SHR 700 Heat Rec Ventilator

Art. no.: 99268

• Airflow up to 723 cfm @ 0.4" PS
• Push-pull configuration
• Removable screw terminal for easy connection
• Dual service doors & reversible electrical box
• External three position switch (Low/Standby/High)


The SHR 700 Commercial Heat Recovery Ventilation system (HRV) complements today's tight buildings.

How it works

Fantech Heat Recovery Ventilators (HRV) are designed to supply air into a building while exhausting an equal amount of contaminated air to the outside. The aluminum heat exchanger core transfers sensible energy between air streams resulting in tempering of the supply air and reduced loads on the HVAC system.

Defrost cycle

A preset defrost sequence is activated at an outdoor air temperature of 23°F and lower. During the defrost sequence, the supply blower shuts down & the exhaust blower switches to high speed to maximize the effectiveness of the defrost strategy. The unit then returns to normal operation, and continues the cycle.

In stock earliest delivery 29.02.19 Show availability
  • Aug 29, 2018
  • Sep 09, 2018
  • 500
  • 500

Technical parameters

Frequency 60 Hz
Voltage (Nominal) 120 V
Phase(s) 1~
Input current 5.58 A
MCA 6.88 A
MOP 15 A
Input power 670 W
Air flow max 723.0 cfm
Static pressure 0.4 in.wg
Dimensions and weights
Weight 215 lb
Certificate CSA, AHRI
Supply Temperature Net Airflow Net Effectiveness



°F (°C)

cfm (L/s)




35 (1.7)

690 (326)



35 (1.7)

518 (244)




95 (35)

690 (326)



95 (35)

518 (244)



A B C D E F G I J K (Drain)

36 1/2 (927)

32 3/16 (818)

13 7/8 (352)

2 3/8 (60)

8 (203)

8 (203)

36 1/4 (921)

22 (559)

32 1/2 (826)

1/2 (13)

Dimensional information is in inches (mm).


Two (2) factory balanced fans with backward curved blades. Motors come with permanently lubricated sealed ball bearings, (TOP) thermal overload protected and maintenance-free operation.

Heat recovery core

Fantech manufactures this fixed plate cross-flow heat exchanger using new 1100 alloy aluminum. Heat exchanger is engineered with a turbulence inducing geometry in order to maximize heat transfer while allowing an effective evacuation of condensate. The plates are hemmed and sealed to ensure no cross-contamination of airstreams. The aluminum core had a plastic handle for easy removal. The SHR 700 features two cores, each 12" x 12" (305 mm x 305 mm) with a 15" (380 mm) depth.


A preset frost control sequence is initiated if the outdoor temperature falls below the set point of 23°F (-5°C). During the initial stage, the supply blower shuts down & the exhaust blower switches into high speed to eliminate frost build-up in the core. The unit then returns to normal operation for the final stage of the frost control sequence at which time the sequence is repeated if the outdoor air temperatures is still below the set point.


Cores, filters and drain pan can be accessed easily from both sides of the HRV from hinged access panels. Cores conveniently slide out with only 15" (380 mm) clearance. Blowers can be accessed from both side of the HRV from fastened access panels. Blowers are easily removed by taking off the access panel and sliding the motor plates out of the HRV. A quick connect allows for fast inspection of blowers.


20 gauge galvanized steel. Baked powder coated paint.


Insulated with 1in. (25 mm) fiberglass with FSK facing for condensation control.


The exhaust and fresh air streams are protected by MERV1 washable filters constructed to meet UL 900. Optional MERV6 filters are direct replacement to the MERV1. Use of MERV6 filters will add an additional system pressure of 0.64 in.wg (160 Pa) at 700 cfm (330 l/s). Additional MERV Rated filters available upon request.


External three (3) position (Low/Stand By/Medium) rocker switch that will offer continuous ventilation. In addition Fantech offers a variety of external controls.


Unit may be suspended by using threaded rod, not supplied, or placed on a platform. Unit shall be adaptable for easy service of electrical components.


Limited lifetime on aluminum core, 3 years on motors, and 3 years on parts.

Requirements and standards
• Complies with the UL 1812 requirements regulating the construction and installation of Heat Recovery Ventilators
• Complies with the CSA C22.2 no. 113 Standard applicable to ventilators
• Technical data was obtained from published results of test relating to AHRI 1060 Standards
BPM 08-14 Bypass module Art. no.: 99300 BPM 08-14 Bypass module $ 427.00 (MSRP)
CO2RT-R Transmitter Art. no.: 99315 CO2RT-R Transmitter $ 585.00 (MSRP)
ECO-TOUCH® Pgrm Wall Control Art. no.: 44929 ECO-TOUCH® Pgrm Wall Control $ 145.00 (MSRP)
EDF1 Multi-Func Ctrl Art. no.: 40375 EDF1 Multi-Func Ctrl $ 50.00 (MSRP)
EDF7 Elec Multi-Funct Dehum Art. no.: 44883 EDF7 Elec Multi-Funct Dehum $ 85.00 (MSRP)
EFD 14-8, Damper, TFB24 Art. no.: 99303 EFD 14-8, Damper, TFB24 $ 477.00 (MSRP)
IR 4 Iris Damper Art. no.: 411234 IR 4 Iris Damper $ 75.00 (MSRP)
IR 5 Iris Damper Art. no.: 411235 IR 5 Iris Damper $ 75.00 (MSRP)
IR 6 Iris Damper Art. no.: 411236 IR 6 Iris Damper $ 80.00 (MSRP)
IR 8 Iris Damper Art. no.: 411237 IR 8 Iris Damper $ 90.00 (MSRP)
MDEH1 Low Voltage Dehumidistat Art. no.: 40172 MDEH1 Low Voltage Dehumidistat $ 26.00 (MSRP)
MGE 4 Metal Exhaust Grill Art. no.: 411106 MGE 4 Metal Exhaust Grill $ 21.00 (MSRP)
MGE 5 Metal Exhaust Grill Art. no.: 411370 MGE 5 Metal Exhaust Grill $ 26.00 (MSRP)
MGE 6 Metal Exhaust Grill Art. no.: 411371 MGE 6 Metal Exhaust Grill $ 27.00 (MSRP)
MGE 8 Metal Exhaust Grill Art. no.: 411244 MGE 8 Metal Exhaust Grill $ 41.00 (MSRP)
MGS 5 Metal Supply Grill Art. no.: 411369 MGS 5 Metal Supply Grill $ 29.00 (MSRP)
MGS 6 Metal Supply Grill Art. no.: 411242 MGS 6 Metal Supply Grill $ 36.00 (MSRP)
MGS 8 Metal Supply Grill Art. no.: 411243 MGS 8 Metal Supply Grill $ 45.00 (MSRP)
RTS2 Pushbutton Timer Art. no.: 40164 RTS2 Pushbutton Timer $ 25.00 (MSRP)
RTS5 Pushbutton Timer Art. no.: 44794 RTS5 Pushbutton Timer $ 45.00 (MSRP)